Arrivé sain et sauf. Les premières impressions étaient tièdes car la planche avait l'air en lambeaux, mais c'était juste du flux non lavé. Il ya une flèche pratique ti vous aider à obtenir les ESP01s branchés dans la bonne façon autour, et soyez prudent, il est très facile de se tromper. Pour l'utiliser comme programmeur pour l'IDE Arduino, il suffit d'ajouter un simple switch entre IO0 et GND pour le mettre en mode flash. C'est simple.

Arrived safe and sound. First impressions were luke warm as the board look tatty, but it was just unwashed flux. There is a handy arrow ti assist you in getting the ESP01s plugged in the right way around, and be careful it is very easy to get wrong. To use it as a programer for the Arduino IDE, all you need to do is add a simple switch between IO0 and GND to get it in to flash mode. Simple.

Arrivé sain et sauf. Les premières impressions étaient tièdes car la planche avait l'air en lambeaux, mais c'était juste du flux non lavé. Il ya une flèche pratique ti vous aider à obtenir les ESP01s branchés dans la bonne façon autour, et soyez prudent, il est très facile de se tromper. Pour l'utiliser comme programmeur pour l'IDE Arduino, il suffit d'ajouter un simple switch entre IO0 et GND pour le mettre en mode flash. C'est simple.

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.

....

....

....

While plug using 3 different item ESP8266 the unit overheat need to remove quick

While plug using 3 different item ESP8266 the unit overheat need to remove quick

While plug using 3 different item ESP8266 the unit overheat need to remove quick

For this Programmer the ESP-Module has to be placed outwards. For me the standard DTR/CTS control for programming is not working using Arduino IDE! First of all I had to solder a pullup resistor between VCC and the CD_PD pin. To put the ESP-01 in programming mode GPIO has to be pulled to ground (soldered a jumper to the pin) followed by pressing the Reset button. For Nral opreation the Jumper should be removed again.

For this Programmer the ESP-Module has to be placed outwards. For me the standard DTR/CTS control for programming is not working using Arduino IDE! First of all I had to solder a pullup resistor between VCC and the CD_PD pin. To put the ESP-01 in programming mode GPIO has to be pulled to ground (soldered a jumper to the pin) followed by pressing the Reset button. For Nral opreation the Jumper should be removed again.

For this Programmer the ESP-Module has to be placed outwards. For me the standard DTR/CTS control for programming is not working using Arduino IDE! First of all I had to solder a pullup resistor between VCC and the CD_PD pin. To put the ESP-01 in programming mode GPIO has to be pulled to ground (soldered a jumper to the pin) followed by pressing the Reset button. For Nral opreation the Jumper should be removed again.

Ottimo prodotto funziona correttamente

Ottimo prodotto funziona correttamente

Ottimo prodotto funziona correttamente

arrivé dans de bonnes conditions

arrived in good conditions

arrivé dans de bonnes conditions

Fait le job

Fait le job

Fait le job

Utile pour esp01s

Utile per esp01s

Utile pour esp01s

BONNES POINTS

GOOD ITEMS

BONNES POINTS